K22033
Material standards K22033 Data sheet, Ex-stock K22033 Chemical, K22033 Property Steelmaking, Blooming, Hot forging, Hot rolling, Heat treatment, Straightening, 100% Ultrasonic flaw detection test, Cold working or Machined. All of these materials conform t
| Product parameters | |
| Material Category:: | Structural Steel |
| Steel Grade: | K22033 |
| Material Technical Standards:: | UNS Series alloy steel |
| Place of Origin: | USA |
Description
Official Test Certificate: issued by TUV - SGS - BV
TECHNICAL SPECIFICATION DATASHEET - UNS K22033
MATERIAL CATEGORY - UNS Series alloy steel
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.33 ~ 0.38
Si (％): 0.15 ~ 0.40
Mn (％): 0.60 ~ 0.80
P (％)≤: 0.025
S (％)≤: 0.025
Cr (％): 0.55 ~ 0.75
Ni (％): 1.10 ~ 1.40
Mo (%): ≤ 0.35
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Tensile strength / σb/MPa|≥: 900 ~ 1050
Yield strength / σs/MPa|≥: 790
Elongation / 5(％)|≥: 11.0
Delivery hardness /HBS|≥: 270
PRODUCT DESCRIPTION
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT
AVAILABLE SHAPES
Round bar / flat bar / hollow bar / strip / forgings
Bright - peeled + polishing, centerless grinding
Forged - ring, discs, shaft
PRODUCT PROFILE & DIMENSIONS
Round bar / Wire rod (Diameter): 5.5mm to 450mm
Square bar / Flat bar: 3mm to 610mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T30 - 300mm X W60 - 1000mm X L1000-12000mm
Sheet steel via cold rolled: T0.5 - 6mm X W10 - 400mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineers, Email: sales@cnlhss.com
TECHNICAL SPECIFICATION DATASHEET - UNS K22033
MATERIAL CATEGORY - UNS Series alloy steel
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.33 ~ 0.38
Si (％): 0.15 ~ 0.40
Mn (％): 0.60 ~ 0.80
P (％)≤: 0.025
S (％)≤: 0.025
Cr (％): 0.55 ~ 0.75
Ni (％): 1.10 ~ 1.40
Mo (%): ≤ 0.35
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Tensile strength / σb/MPa|≥: 900 ~ 1050
Yield strength / σs/MPa|≥: 790
Elongation / 5(％)|≥: 11.0
Delivery hardness /HBS|≥: 270
PRODUCT DESCRIPTION
Alloy structural steel is provided with higher yield strength, tensile strength, endurance strength, yield ratio (about 0.85 generally ) enough plasticity and toughness.
The concentration of alloy element of this kind of steel is quite high, mainly are corrosion resistant steel, heat resistant steel, wear resistant steel, and other special steels of physical and chemical properties. Alloy structural steel has preferable mechanical property than that of carbon structural steel, high performance of heat treatment especially.
The alloy is usually produced by EAF /VD /LF followed by electroslag refining (ESR) if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different level according to the buyers' requirements.
Bars are usually supplied bright in the annealed condition, or bright annealing specially.
Final heat treatment - heat treatment / QT
AVAILABLE SHAPES
Round bar / flat bar / hollow bar / strip / forgings
Bright - peeled + polishing, centerless grinding
Forged - ring, discs, shaft
PRODUCT PROFILE & DIMENSIONS
Round bar / Wire rod (Diameter): 5.5mm to 450mm
Square bar / Flat bar: 3mm to 610mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T30 - 300mm X W60 - 1000mm X L1000-12000mm
Sheet steel via cold rolled: T0.5 - 6mm X W10 - 400mm X L1000 - 2000mm
Steel strip via cold rolled: T0.1 - 3mm X W5 - 200mm X L (or in coil form)
Forging piece: stepped shafts with flanks / discs /tubes /slugs /donuts /cubes /other different shapes based on OEM.
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, pleased to EMAIL our resident team of qualified production engineers, Email: sales@cnlhss.com
