X45CrSi9
Description X45CrSi9 datasheet, X45CrSi9 Chemical, X45CrSi9 Properties Steelmaking, Blooming, Hot forging, Hot rolling, Heat treatment, Straightening, 100% Ultrasonic flaw detection test, Cold working or Machined. All of these materials conform to Militar
| Product parameters | |
| Material Category:: | Stainless Steel |
| Steel Grade: | X45CrSi9 |
| Material Technical Standards:: | NF EN |
| Specification Code:: | NF EN 10090 - 1998 |
| Place of Origin: | France |
Description
TECHNICAL DATASHEET - NF X45CrSi9
OFFICIAL TEST CERTIFICATE: issued by TUV - SGS - BV
MATERIAL CATEGORY - Valve Steel
Technical standards - NF EN 10090 - 1998
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.40 ~ 0.50
Si (％): 2.70 ~ 3.50
Mn (％): ≤ 0.60
P (％)≤: 0.040
S (％)≤: 0.030
Cr (％): 8.00 ~ 10.0
Ni (％): ≤ 0.50
Mo (%): -
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Annealed temperature /℃: 780 ~ 820
Quenched temperature /℃: 1020 ~ 1070, air / oil
Tempered temperature /℃: 720 ~ 820
Tensile strength,σb/≥ MPa: 900 ~ 1100
Yield strength, σ0.2/≥ MPa: 700
Elongation, δ ≥(％): 14.0
Reduction of area, (%): 40
PRODUCT DESCRIPTION
The alloy is usually produced by AOD / VOD /VIM followed by electroslag refining (ESR) / VAR if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different levels according to the buyers' requirements.
Bars are usually supplied black/bright in the annealed condition.
Final heat treatment - Quenched and tempered thermal treatment
PRODUCT PROFILE & FORMS DIMENSIONS
Round bar (Diameter): 5.5 to 600mm
Square bar / Flat bar: T3.0 to 500mm X W3.0 ~ 1200mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T3.0 - 200mm X W1000- 2500mm X L1000-12000mm
Sheet steel via cold rolled: T0.5 - 3mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.10 - 3mm X W5.0 - 600mm X L (or in coil form)
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, you can do as follows:
EMAIL our qualified production engineers, E-mail: lh.steel@hotmail.com
Reach to our sales department directly: sales@cnlhss.com
OFFICIAL TEST CERTIFICATE: issued by TUV - SGS - BV
MATERIAL CATEGORY - Valve Steel
Technical standards - NF EN 10090 - 1998
CHEMICAL COMPOSITION (WEIGHT %)
C (％): 0.40 ~ 0.50
Si (％): 2.70 ~ 3.50
Mn (％): ≤ 0.60
P (％)≤: 0.040
S (％)≤: 0.030
Cr (％): 8.00 ~ 10.0
Ni (％): ≤ 0.50
Mo (%): -
MECHANICAL PROPERTIES UNDER ROOM TEMP.
Annealed temperature /℃: 780 ~ 820
Quenched temperature /℃: 1020 ~ 1070, air / oil
Tempered temperature /℃: 720 ~ 820
Tensile strength,σb/≥ MPa: 900 ~ 1100
Yield strength, σ0.2/≥ MPa: 700
Elongation, δ ≥(％): 14.0
Reduction of area, (%): 40
PRODUCT DESCRIPTION
The alloy is usually produced by AOD / VOD /VIM followed by electroslag refining (ESR) / VAR if necessary for special purpose.
Bars and, where applicable, forgings are subjected to ultrasonic examination based on the different levels according to the buyers' requirements.
Bars are usually supplied black/bright in the annealed condition.
Final heat treatment - Quenched and tempered thermal treatment
PRODUCT PROFILE & FORMS DIMENSIONS
Round bar (Diameter): 5.5 to 600mm
Square bar / Flat bar: T3.0 to 500mm X W3.0 ~ 1200mm
Length: Fixed length or random length or based on the customer's special requirement.
Heavy/middle plate via hot rolled: T3.0 - 200mm X W1000- 2500mm X L1000-12000mm
Sheet steel via cold rolled: T0.5 - 3mm X W600- 1000mm X L1000 - 2000mm
Steel strip via cold rolled: T0.10 - 3mm X W5.0 - 600mm X L (or in coil form)
TECHNICAL SALES ASSISTANCE
If you meet further on any technical enquiry, you can do as follows:
EMAIL our qualified production engineers, E-mail: lh.steel@hotmail.com
Reach to our sales department directly: sales@cnlhss.com
